Rain Gutter Solutions(208) 724-7885
Service

Seamless Gutter Installation & Replacement

Aluminum gutter formed on site and custom cut to the measured length of each roof run, with corners and end caps fitted to the home.

About seamless gutter installation & replacement

We form the gutter on site from a single coil and custom cut each run to the home’s measured roofline. Corners, end caps and outlets complete the system, and we fit and seal those connections carefully.

Sizing is done off the roof area that actually drains into each run, not off a rule of thumb. A 5 inch K-style handles most Treasure Valley homes. Steeper pitches and larger roof planes get 6 inch with oversized downspouts, because a gutter that cannot keep up in a July thunderstorm will sheet water over the front lip exactly where you least want it.

Colour is matched to the existing trim from a standard range at no extra cost. Fascia is inspected before anything is hung, and if it needs repair we quote that separately rather than folding it into the total. Hanging new gutter on soft fascia just moves the problem one season down the road.

Most of what we do is replacement rather than first fit. Somebody in Boise or Meridian has gutter that has been patched twice and is failing again, and they want to know whether to repair it once more or replace the lot. We will tell you which, and the price section below sets out exactly what moves the number so a replacement quote is not a mystery.

Copper gutter and downspout turned out over a lower roof, set against dark board and batten siding
Copper gutter and downspout turned out over a lower roof, set against dark board and batten siding
What you get

What is included

  • Seamless aluminum formed on site and custom cut to each measured run
  • Hidden hangers screwed into the fascia board and spaced center-to-center for the system and site conditions
  • Downspouts sized and placed to move water clear of the foundation
  • Mitred corners cut and sealed on site rather than bought as pre-formed boxes
  • Full fascia inspection before anything is hung, with any rot flagged and quoted separately
  • Old gutter taken down and hauled away
  • Remove and discard debris from the gutters and clear downspouts as included in the written scope
  • Repair loose hangers included in the written scope
  • Property cleanup included before the crew leaves
Method

How we do it

  1. Measure the roof, not the wall

    We work out the square footage draining into each run, the pitch, and where the water is going to concentrate. That decides 5 inch or 6 inch and how many downspouts you need. Most undersized systems we replace were sized off the length of the wall.

  2. Check the fascia

    A gutter is only as sound as the board it hangs on. We check for soft spots and previous water damage before quoting, because that changes the job and you should hear about it before you commit.

  3. Custom cut the gutter on site

    The machine forms gutter from a coil and each run is cut to the length measured for your home. Corners, end caps and outlets are fitted as needed.

  4. Hang, mitre and seal

    Hidden hangers at spacing suited to your snow load. Corners mitred and sealed on site so they match the run rather than sitting proud of it.

  5. Finish and tidy the installation

    We complete the fittings, remove job debris, clear downspouts included in the scope, and leave the property clean.

Worth checking

Signs you need installation

If you recognise more than one of these it is worth having someone look, and looking is free.

  • Water sheets over the front edge in heavy rain instead of running to the downspout
  • Leaking corners or end caps, or sections pulling loose from the roofline
  • Staining or peeling paint on the fascia board behind the gutter
  • Sections pulling away from the roofline or visibly sagging in the middle
  • Pooling and mud splash against the foundation after a storm
  • Gutter that was already old when you bought the house
Our work

Recent installation work

  • Finished seamless gutter and downspout on the covered entry of an olive green Treasure Valley home
    Finished seamless gutter and downspout on the covered entry of an olive green Treasure Valley home
  • Rain Gutter Solutions crew member on a ladder fitting new gutter to a Treasure Valley home
    Rain Gutter Solutions crew member on a ladder fitting new gutter to a Treasure Valley home
  • New construction home with porch columns and freshly hung seamless gutter
    New construction home with porch columns and freshly hung seamless gutter
Pricing

What drives the price

We quote on site rather than over the phone, because these vary enough between houses that a phone number would be a guess. Here is exactly what we are weighing up.

Linear footage
The single biggest factor. A simple ranch with four runs costs a fraction of a two storey with dormers and multiple valleys.
Gutter size and gauge
6 inch costs more than 5 inch per foot and needs larger downspouts, but on a big or steep roof it is the difference between a system that works and one that overflows twice a year.
Fascia condition
If the board behind the gutter is soft it has to be repaired first. We quote this separately so you can see exactly what is gutter and what is carpentry.
Height and access
Two and three storey elevations, steep pitches and tight side yards all take longer and need more setup.
Number of corners and downspouts
Every mitre and every outlet is hand cut and sealed. A cut up roofline costs more per foot than a long straight one.

Ready for a free estimate?

We come out, measure in person, and leave you with an itemized written quote. We’ll follow up to answer questions, with no pressure to book.

Call (208) 724-7885Request online
Straight answers

Questions about installation

Is seamless gutter actually better, or is it just a sales line?

Seamless gutter is formed on site and cut to the measured length of each run, reducing the number of joints along a straight section. A complete system still has corners, end caps and outlets, which are fitted and sealed as part of the installation.

How long does a seamless gutter installation take?

Most single family homes are a one day job. The gutter is formed on site as we go, so there is no waiting on an order. A large or complex roofline, or a job that needs fascia repair first, can run into a second day. We will tell you which it is when we quote.

Do I need 5 inch or 6 inch gutter?

It depends on the roof area draining into each run and the pitch. Most Treasure Valley homes are fine on 5 inch K-style. Steeper roofs shed water faster and larger roof planes collect more of it, and both push you toward 6 inch with 3x4 downspouts. We work it out from your actual roof rather than guessing.

What colours can I get?

There is a standard colour range matched to common trim and fascia colours, and colour matching is included rather than an upgrade. Bring us a sample or we will match off the existing trim on site.

Installation across the valley

Available throughout the regular Treasure Valley service area, with free on-site estimates and no travel charge. We also take work farther out; a travel charge applies and is quoted before scheduling.

Other services